Procurement Technical Assistance Centers (PTACs) are an official government contracting resource for small businesses. Find your local PTAC (opens in new window) for free government expertise related to contract opportunities.

Page 4 of 4 Page 1 of 2 Please note that this is NOT a request for quotes or proposals, the Government is seeking information for market research purposes only. The Department of Veterans Affairs, Network Contracting Office NCO2 is currently conducting a market survey on behalf of the Buffalo VAMC to locate qualified firms capable of fulfilling a brand name or equal requirement for various lighting, blinds and controls. Those capable of providing these supplies should submit a statement regarding their capability on a document containing the official company letterhead. Additionally, those interested and capable shall be authorized distributors, provide a designated point of contact, the business Unique Entity Identifier (UEI), and the business socioeconomic status in their response to this posting. The Veterans Health Administration prohibits the use of gray market items in their Medical Centers. Gray market items are considered to be items outside of the original equipment manufacturer s intended distribution channels. This market research is for vendors capable of providing SUPPLIES ONLY, installation/service is not required. Required products, quantities and minimum requirements; All lighting products shall meet the specifications listed below them Five Hundred and Fifty (550) 2 feet x 2 feet Architectural Recessed LED Lighting 3400 Lumens 120-277 Voltage LED dims to 1% (0-10 volt dimming) 82 CRI, 3500 K Color Temperature Length: 24 in Width: 23-3/4 in Depth: 3-5/8 in Lay-in Grid (exposed or concealed grid) Mounting Buy America(n) Act Compliant An example of 2 ft x 2 ft Architectural Recessed LED Lighting is Lithonia 2BZL2 34L EZ1 LP835 BAA. Three Hundred and Fifty (350) 2 feet x 4 feet Architectural Recessed LED Lighting 4000 lumens 120-277 Voltage LED dims to 1% (0-10 volt dimming) 82 CRI, 4000K Color Temperature Length: 48 in Width: 23-3/4 in Depth: 3-5/8 in Lay-in Grid (exposed or concealed grid) Mounting Buy America(n) Act Compliant An example of 2 ft x 2 ft Architectural Recessed LED Lighting is Lithonia 2BZL4 40L EZ1 LP840 BAA One Hundred Seventy-Five (175) 4 feet Low Profile LED Wraparound Lighting 4000 Lumens Curved, ribbed diffusers w/ trim rings 120-277 Voltage LED dims to 1% (0-10 volt dimming) 82 CRI, 4000K Color Temperature Wired low voltage control device without lumen management Length: 48 in Width: 5.50 in Depth: 3.50 in Integrated Passive Infrared Dual Technology Occupancy Sensor An example of a 4 ft Low Profile LED Wraparound Lighting is Lithonia BLWP4 40L ADPT EZ1 LP840 N100 NESPDT7 One Hundred Seventy-Five (175) 4-feet Low Profile LED Wraparound Lighting 4000 Lumens Curved, ribbed diffusers w/ trim rings 120-277 Voltage LED dims to 1% (0-10 volt dimming) 82 CRI, 4000K Color Temperature Wired low voltage control device without lumen management Length: 48 in Width: 5.50 in Depth: 3.50 in Integrated Passive Infrared Dual Technology Occupancy Sensor Fixture with embedded sensor dims to approximately 10% light output when unoccupied An example of a 4-feet Low Profile LED Wraparound Lighting is Lithonia BLWP4 40L ADPT EZ1 LP840 N100 NESPDT7 DIM10 Two Hundred (200) 2 feet Low Profile LED Wraparound Lighting 3300 Lumens Curved, ribbed diffusers w/ trim rings 120-277 Voltage LED dims to 1% (0-10 volt dimming) 82 CRI, 4000K Color Temperature Length: 24 in Width: 5.50 in Depth: 3.50 in Buy America(n) Act Compliant An example of a 2 ft Low Profile LED Wraparound Lighting is Lithonia BLWP2 33L ADPT EZ1 LP840 BAA Three Hundred Fifty (350) 4-feet Low Profile LED Wraparound Lighting 4000 Lumens Curved, ribbed diffusers w/ trim rings 120-277 Voltage LED dims to 1% (0-10 volt dimming) 82 CRI, 4000K Color Temperature Length: 48 in Width: 5.50 in Depth: 3.50 in Buy America(n) Act Compliant An example of a 4 ft Low Profile LED Wraparound Lighting is Lithonia BLWP4 40L ADPT EZ1 LP840 BAA Thirty-Seven (37) 6-inch Downlight LED Fixture 6-inch Round Color Temperature: 3500K Lumen: 1500 Finish: Matte Diffuse Multi-Voltage Buy America(n) Act Compliant An example of a 6-inch Downlight LED Fixture that meets these specifications is Lithonia LDN6 35/15 LO6AR LD MVOLT EZ10 BAA All ribbon lighting and associated products shall meet the specifications listed below them and have the capability to work in conjunction with each other. Fifty (50) Feet Full Spectrum LED Ribbon Lighting Operating Voltage 24 V Power Consumption 4.4 W/ft (14.4 W/m) Current (mA) - 24V 183 mA/ft (600.2 mA/m) LED Pitch 18 LEDs/ft (60 LEDs/m) Colors Red, Green, Blue Lumens 165 lm/ft (541 lm/m) All LEDs at 100% LED Beam Angle 120° Lamp Life 50,000 Hours An example of Full Spectrum LED Ribbon Lighting that meets these specifications is ACOLYTE RB0RGB204.4RGB -RIBBON Fifty (50) Feet Mounting Channel for LED ribbon Lighting An example of mounting channel that works with the ribbon lighting is Acolyte SC6 CHANNEL One (1) Five Channel LED Lighting Interface 12-24 VDC output 8 A max per channel output 12 V max power output: 96 W/Channel 24 V max power output: 192 W/Channel Width: 2.87 in (73 mm) Length: 6.45 in (164 mm) Depth: 1.49 in (38 mm) An example of a Five Channel LED Lighting Interface that meets these specifications is ACOLYTE DMXINFLCD5 Two (2) LED Drivers 24 VDC output IP65 wet location 240 W (High Wattage) Width: 11.8 in, Length: 9.61 in, Depth: 1.53 in. An example of an LED driver that meets these specifications is Acolyte DRVW24240 One (1) Lighting Interface Controller 1 Zone 5 - 15V DC input Change color, brightness, saturation, speed & more Touch Capacitive Programmable with ESA2 PC/Mac software Up to 36 preset scenes via 6 buttons 1 USB port and 8 contact ports Built-in flash memory An example of a Lighting Interface Controller that meets these specifications Acolyte AWCRGBWW One (1) Led Driver 24 VDC output IP65 wet location 240 W (High Wattage) An example of an LED driver that meets these specifications is Acolyte DRVW1212 One hundred (100) LED Ribbon Lighting Flat Mounting Clips Screw Head Diameter 0.27 in Screw Head Height 0.36 in Clip Length 1.07 in Clip Width 0.24 in Screw Hole Diameter 0.09 in Screw Hole Distance 0.88 in An example of an LED Ribbon Lighting Flat Mounting Clip that meets these specifications is Acolyte RBMNTSIL All control products shall meet the specifications listed below them and have the capability to work in conjunction with each other. Twenty (20) - dimming modules Current rating of 8-Amps Voltage rating of 120/277-Volts at 50/60-Hz Controls up to 60-Milli-Amps of 0 to 10-Volt controlled fixtures together Switches up to 8-Amps 0 to 10-Volt Control link automatically sources or sinks to the third-party fixtures Receives wireless inputs from up to 10 Pico remote controls, 10 Radio Power Saver occupancy/vacancy sensors and 1 Radio Power Saver daylight sensor Supports easy mounting to a US-style junction box through a standard size knockout An example of a dimming module that meets these specifications is Lutron RMJS-8TN-DV-B Four (4) - Wireless Button controls Frequency/Channel: 431.0 - 437.0 MHz 2 buttons Color: Ivory Button marking codes: light Battery Powered with 10-year lifespan Can provide control of blinds, curtains, or lighting devices within a range of 30 ft (9 m) through walls and 60 ft (18 m) line-of-sight An example of a wireless button control that meets these specifications is Lutron PJ2-2B-GIV-L01 Thirty-five (35) - Wireless Button controls Frequency/Channel: 431.0 - 437.0 MHz 3 buttons with raise/lower Color: Ivory Button marking codes: light Battery Powered with 10-year lifespan Can provide control of blinds, curtains, or lighting devices within a range of 30 ft (9 m) through walls and 60 ft (18 m) line-of-sight An example of a wireless button control that meets these specifications is Lutron PJ2-3BRL-GIV-L01 Ten (10) - Wireless Button controls Frequency/Channel: 431.0 - 437.0 MHz 3 buttons with raise/lower Color: Black Button marking codes: light Battery Powered with 10-year lifespan Can provide control of blinds, curtains, or lighting devices within a range of 30 ft (9 m) through walls and 60 ft (18 m) line-of-sight An example of a wireless button control that meets these specifications is Lutron PJ2-3BRL-GIV-L01 Twenty-three (23) - Wireless button control wall box adapters Allows the remotes in part 2 & 3 section III to be mounted to existing wall boxes. An example of a wireless button control wall box adapters that meets these specifications is Lutron PICO-WBX-ADPAT Thirty Seven (37) - Emergency power control switches Sensing input: 120V - 277V Load rating: 120V - 277V (20A) Ballast load rating: 20A (120-277V) Incandescent load: 1200W (120V) / 1500W (277V) Mounting: 4-11/16 Junction Box w/ double gang ring Rating: UL94V-0 Color: White Flush Mounted Size: 5 x 5 x 0.2 (W X L X D) Body Size: 3.5 x 2.75 x 1.5 (W X L X D) During a utility power interruption, automatically bypasses the normal lighting controls, turning the emergency lights ON, regardless of switch position. An emergency power control switch that meets these specifications is FKA LUT-ALCR-D One (1) - Base control unit Four (4) light zones RF Frequency: 434 MHz Input power: 120 127 V~ 50/60 Hz, 220 240 V~ 50/60 Hz Fit into a 4-gang U.S. backbox Sixteen (16) total available scenes, plus Off scene Master override buttons to raise and lower all lights Built-in infrared (IR) receiver External IR connection Built-in astronomic timeclock. Info screen shows zone light level percentage, energy savings, zone labeling, and programming An example of a base control unit that meets these specifications is Lutron QSGRJ-4P One (1) - Faceplate Fits the base control unit listed in part f. of section III (above) Satin Nickel Finish An example of a faceplate that meets these specifications is Lutron QSGFP-1TSN Ten (10) - Ten-volt interface controllers 100-277 V~ forward, reverse, and center phase control input capability Provides 0 10 V- control and switching capabilities to switch and dim current sourcing fluorescent ballasts and LED drivers. Switches and dims current sourcing 0 10 Velectronic dimming ballasts / drivers powered by 100 277 V~. Switches up to 16 A of electronic capacitive ballasts / drivers. Switches motors up to 1/2 HP @ 100-120 V~, 1 ½ HP @ 200 277 V~ and 5 A @ 230 V~ CE. Up to five Ten Volt Interfaces may be connected to one Control Unit zone. This allows one zone to control up to five 16 A circuits of Electronic Dimming Ballasts / Drivers or five motors Provides 100 277 V~ power to loads. Requires 100 277 V~ power for internal operations A ten-volt interface control that meets these specifications is Lutron GRX-TVI Four (4) Two button wall-station switches Low-voltage type PELV (Class 2: USA). Operating voltage: 24 V Meets IEC 801-2. Tested to withstand 15 kV electro-static discharge without damage or memory loss Accept up to two #18 AWG (1.0 mm2) typical. Typical backbox dimensions: 3.74 in. (95 mm) high, 2.17 in. (55 mm) wide, 2.75 in. (70 mm) deep Receives up to two contact closure inputs via a connector on the back of the wall-station Large rounded backlit buttons Satin nickel finish A two-button wall-station switch that meets these specifications is Lutron QSWS2-2BN-SN-EGN Two (2) 5 Button wall-station switches 5-Button wall-station with Raise/Lower Receives up to two contact closure inputs via a connector on the back of the wall-station Low-voltage type PELV (Class 2: USA). Operating voltage: 24 V Meets IEC 801-2. Tested to withstand 15 kV electro-static discharge without damage or memory loss Accept up to two #18 AWG (1.0 mm2) typical. Typical backbox dimensions: 3.74 in. (95 mm) high, 2.17 in. (55 mm) wide, 2.75 in. (70 mm) deep Receives up to two contact closure inputs via a connector on the back of the wall-station Large rounded backlit buttons Satin nickel finish A 5-button wall-station that meets these specifications is Lutron QSWS2-5BRLN-SN-EGN Two (2) Network interfaces for integrating shades and blinds Operating voltage: 24 36 V- 65 mA Monitoring: Current scene, zone level, button presses, shade group levels. Control: Scene selection, scene lockout, zone lockout, sequencing, zone raise/lower, master raise/lower, set shade group level, simulate button press/release. RS232 Connection: Standard 9-pin female serial connector on interface Ethernet Connection: Standard CAT5 (or better) cable, 328 ft (100 m) maximum, connects the QSE-CI-NWK-E interface to a PC or other Ethernet source. Supports MDI/MDIX auto-crossover (no crossover cable needed). Auto-negotiation of 10 or 100 Mbps speed and full- or half-duplex operation. An example of a network interface for integrating shades and blinds that meets these specifications is Lutron QSE-CI-NWK-E One Thousand (1000) Feet of Lighting Control Cable 1000-foot spool Twisted, shielded 22 AWG data pair Twisted, unshielded 12 AWG power pair low capacitance data pair under 24 pF/FT Plenum rated PVC jacket with a blue stripe NEC CL3P, RoHS compliant An example of lighting control cable that meets these specifications is FKA LUTRON-P-RBL Sixteen (16) Wireless Battery-Powered Occupancy Sensor Operating voltage: 3 V- Operating current: 14 A nominal Requires one CR 123 lithium battery with 10-year lifespan Non-volatile memory (saved changes are stored during power loss) Local load controls must be located within 60 ft (18 m) line-of-sight, or 30 ft (9 m) through walls, of a sensor 360 coverage ranges from 324 ft2 (30.2 m2) to 676 ft2 (62.4 m2), depending on mounting height Auto-On Low-Light feature will turn lights on automatically only if there is less than approximately 10 Lux (1 fc) of ambient light White finish An example of a wireless battery-powered occupancy sensor that meets these specifications is Lutron ULRF2-OCR2B-P-WH Two (2) Base unit controllers Six (6) light zones RF Frequency: 434 MHz Input power: 120 127 V~ 50/60 Hz, 220 240 V~ 50/60 Hz Fit into a 4-gang U.S. backbox Sixteen (16) total available scenes, plus Off scene Master override buttons to raise and lower all lights Built-in infrared (IR) receiver External IR connection Built-in astronomic timeclock. Info screen shows zone light level percentage, energy savings, zone labeling, and programming An example of a base control unit that meets these specifications is Lutron QSGRJ-6P Two (2) Faceplate Fits the base control unit listed in part n. of section III (above) Satin Nickel Finish An example of a faceplate that meets these specifications is Lutron QSGFP-2TSN Two (2) - Phase-Adaptive Power Module Provides dimming control for 1 zone of a full 16 A lighting load Mount in 2-gang U.S. wall-box, 3.5 in (89 mm) deep or 4 × 4 in (102 × 102 mm) junction box, 2.1 in (53 mm) deep. Capacity: Full 16 A 120 V~: 1920 W 120 277 V~: 1920 4432 W 220 240 V~: 3520 3840 W Frequency: 50/60 Hz Load (output) power: Phase independent of control device/control voltage Operates these sources with a smooth, continuous, Square Law dimming curve: Incandescent (tungsten) Halogen Magnetic low-voltage transformer (iron core) Electronic (solid-state) low-voltage transformer (must be manufacturer-approved for reverse-phase control dimming) Neon/Cold cathode Each terminal accepts up to two 12 AWG (2.5 mm2) wires An example of a Phase-Adaptive Power Module that meets these specifications is Lutron PHPM-PA-DV-WH Two (2) Dual Remote Pedestals Holds (2) Lutron Pico remotes at convenient angle for tabletop use Color: Black An example of a dual remote pedestal that meets these specifications is Lutron L-PED2-BL. All electronic shades and associated controls shall meet the specifications listed below them and have the capability to work in conjunction with each other. One (1) Two button wall-station switches with raise/lower Low-voltage type PELV (Class 2: USA). Operating voltage: 24 V Meets IEC 801-2. Tested to withstand 15 kV electro-static discharge without damage or memory loss Accept up to two #18 AWG (1.0 mm2) typical. Typical backbox dimensions: 3.74 in. (95 mm) high, 2.17 in. (55 mm) wide, 2.75 in. (70 mm) deep Receives up to two contact closure inputs via a connector on the back of the wall-station Large rounded backlit buttons Standard engraving Insert style Satin Matte Snow color Includes faceplate Shade only control features: - Used to control multiple groups of shades independently from a single-gang keypad A two-button wall-station switch that meets these specifications is Lutron QSWS2-2BRLI-SW-E01 One (1) - 5-Button wall-station switches raise/lower Low-voltage type PELV (Class 2: USA). Operating voltage: 24 V Meets IEC 801-2. Tested to withstand 15 kV electro-static discharge without damage or memory loss Accept up to two #18 AWG (1.0 mm2) typical Typical backbox dimensions: 3.74 in. (95 mm) high, 2.17 in. (55 mm) wide, 2.75 in. (70 mm) deep Receives up to two contact closure inputs via a connector on the back of the wall-station Large rounded backlit buttons Standard engraving Insert style Satin Matte Snow color Includes faceplate Shade only control features: - Used to control multiple groups of shades independently from a single-gang keypad Includes faceplate A two-button wall-station switch that meets these specifications is Lutron QSWS2-5BRLI-SW-E01. One (1) Dual 2 button wall-station switches with raise/lower Low-voltage type PELV (Class 2: USA). Operating voltage: 24 V Meets IEC 801-2. Tested to withstand 15 kV electro-static discharge without damage or memory loss Accept up to two #18 AWG (1.0 mm2) typical. Typical backbox dimensions: 3.74 in. (95 mm) high, 2.17 in. (55 mm) wide, 2.75 in. (70 mm) deep Receives up to two contact closure inputs via a connector on the back of the wall-station Large rounded backlit buttons Standard engraving Insert style Satin Matte Snow color Includes faceplate Shade only control features: - Used to control multiple groups of shades independently from a single-gang keypad A two-button wall-station switch that meets these specifications is Lutron QSWS2-2RLDI-SW-E01 Six (6) - 3 Button wall-station with raise/lower Low-voltage type PELV (Class 2: USA). Operating voltage: 24 V Meets IEC 801-2. Tested to withstand 15 kV electro-static discharge without damage or memory loss Accept up to two #18 AWG (1.0 mm2) typical. Typical backbox dimensions: 3.74 in. (95 mm) high, 2.17 in. (55 mm) wide, 2.75 in. (70 mm) deep Receives up to two contact closure inputs via a connector on the back of the wall-station Large rounded backlit buttons Standard engraving Insert style Satin Matte Snow color Includes faceplate Lights and Shades: Top column controls only lights and has a programmable column type (choose from the list on the following pages). Bottom column controls only shades and has a programmable column type. A three-button wall-station switch that meets these specifications is Lutron QSWS2-3BRLI-SW-EGN Twelve (12) - Power supplies Input: 120-240 V~ 50/60 Hz 1.2 A Output: 35 V- 0.143 A 5 W Output terminal wiring: 22 AWG 12 AWG Capable of powering window shade rollers and associated controls Dimensions: 2.75 in 4 in 1.25 in An example of a power supply that meets these specifications is Lutron QS Link Plug-In Power Supply QSPS-J-1-35V. Five Hundred (500) Feet - Low-Voltage Cable for Class 2 Applications 4 Conductors #18 Black, #18 Red, #22 White, #22 Violet, # 24 Drain Drain, Violet, White cable wrapped together in foil shield All wire wrapped in an outer PVC Jacket A Low-Voltage Cable for Class 2 Applications that meets these specifications is Lutron Grafik Eye GRX-CBL-346S-500 Two (2) Ten-output power supply for powered window blinds Ten NEC® Class 2/PELV outputs input: 120-240 V~ 50/60 Hz 10 A Each output: 35 V- 143 mA 5 W No replaceable fuses required for overload/mis-wire protection Smart diagnostics verify system communication and reduce installation time Dimensions: 10.88 in 18 in 4.16 in An example of a ten-output power supply for powered window blinds that meets these specifications is Lutron QSPS-10PNL Three (3) Wired Power Roller Shades Shall not exceed 38 dBA measured 3 ft from the EDU 24-36 V low-voltage power Programmable stop points Window coverage with the smallest possible light gaps, 0.75 in. Composition: 100% Polyester with Acrylic Foamed Backing (Off-White) Color: Porpoise Operator side: right Top Treatment Span: Split Top Treatment Vendor to field verify Dimensions to ensure proper fit. An example of a Wired Power Roller Shades that meets these specifications is Sivoia QS Wired Roller 100, Value Premiere 0% Porpoise (BP-V70-0) Sixteen (16) Wired Power Roller Shades Shall not exceed 38 dBA measured 3 ft from the EDU 24-36 V low-voltage power Programmable stop points Window coverage with the smallest possible light gaps, 0.75 in. Composition: 100% Polyester with Acrylic Foamed Backing (Off-White) Color: Porpoise Operator side: right Vendor to field verify Dimensions to ensure proper fit. An example of a Wired Power Roller Shades that meets these specifications is Sivoia QS Wired Roller 64, Value Premiere 0% Porpoise (BP-V70-0) Two (2) Wired Power Roller Shades Shall not exceed 38 dBA measured 3 ft from the EDU 24-36 V low-voltage power Programmable stop points Window coverage with the smallest possible light gaps, 0.75 in. Opacity: Blackout Composition: 100% Polyester with Acrylic Foamed Backing (Off-White) Color: Porpoise Operator side: right Vendor to field verify Dimensions to ensure proper fit. An example of a Wired Power Roller Shades that meets these specifications is Sivoia QS Wired Roller 100, Value Premiere 0% Porpoise (BP-V70-0) Six (6) Wired Power Roller Shades Shall not exceed 38 dBA measured 3 ft from the EDU 24-36 V low-voltage power Programmable stop points Window coverage with the smallest possible light gaps, 0.75 in. Opacity: Blackout Composition: 100% Polyester with Acrylic Foamed Backing (Off-White) Color: Porpoise Operator side: right Vendor to field verify dimensions to ensure proper fit. An example of a Wired Power Roller Shades that meets these specifications is Sivoia QS Wired Roller 64, Value Premiere 0% Porpoise (BP-V70-0) The North American Industry Classification Systems (NAICS) is 335129. The purpose of this notice is to gain knowledge of potential qualified sources and their size classification/ socioeconomic statuses relative to NAICS 335129. Responses to this notice will be used by the Government to make appropriate acquisition decisions. Responses should include company/individual name, a service capability statement, examples of similar facilities for which you have provided services to, UEI number, address, point of contact and social-economic category (ex: SBVOSB, VOSB, 8(a), HUBZone, WOSB, EDWOSB, Small Business). If your firm is a Service-Disabled Veteran Owned or Veteran Owned Small Business, you must be VERIFIED in VetBiz (see internet site: http://vip.vetbiz.gov). Contractor must be registered in System for Award Management (SAM), (see internet site: http://www.sam.gov). Responses to this notice must be submitted in writing via email to lindsay.goldsmith@va.gov and must be received not later than January 30, 2023 10:00 AM EST. No telephone inquiries will be accepted.